	U.S. Gate Supply I: (818) 765-3636 This e-mail address is being protected from spambots. You need JavaScript enabled to view it.		U.S. Gate Supply II: (858) 271-7336 This e-mail address is being protected from spambots. You need JavaScript enabled to view it.

	U.S. Gate Supply III: (951) 778-2500 This e-mail address is being protected from spambots. You need JavaScript enabled to view it.		U.S. Gate Supply IV: (805) 462-8877 This e-mail address is being protected from spambots. You need JavaScript enabled to view it.

HomeProductsGate Hardware ProductsRadio Receivers & Remote Controls

Gate Hardware

Radio Receivers & Remote Controls

LiftMaster 370LM Mini 3-Button Remote Control

Electronic Features:

Are you always on the go? Our mini 3-button remote control is a miniature version of our 3-button remote control, and just as powerful. It can open and close 3 garage doors or gates, turn opener lights on/off, and/or turn on lights and small appliances in your home. And the best part is that it can fit almost anywhere – in your purse, your pocket, or even on your keychain. It features Security+® rolling code technology that sends a brand new code every time it is used, keeping you, your family, and your belongings safe and secure. One 5-year 3-volt battery is included.

GENERAL SPECIFICATIONS:

Your garage door opener has a purple learn button, or
Your garage door opener motor head has a purple antenna, or
Your original remote has silver buttons with glowing blue lights, or
Your original remote has black buttons

LiftMaster 371LM 1-Button Remote Control

Electronic Features:

Our basic 1-button remote control isn't so basic. It can operate a single garage door or gate, or turn your garage door opener lights on/off. You can also use it as an extra remote control to turn on lights or small appliances inside your home – all from the comfort of your car. It features Security+® rolling code technology that sends a brand new code every time it is used. One 5-year 3-volt battery is included.

The MHz frequency of your garage door opener will determine what remote controls will work with your system. See below to find out which remote to order.

GENERAL SPECIFICATIONS:

Order the 371LM if:

Your garage door opener has a purple learn button, or
Your garage door opener motor head has a purple antenna, or
Your original remote has silver buttons with glowing blue lights, or
Your original remote has black buttons

LiftMaster 373LM 3-Button Remote Control

Electronic Features:

Our basic 3-button remote control isn't so basic. It can operate up to 3 garage doors or gates, and/or turn your garage door opener lights on/off. You can also use it as an extra remote control to turn on lights or small appliances inside your home – all from the comfort of your car. It features Security+® rolling code technology that sends a brand new code every time it is used. One 5-year 3-volt battery is included.

The MHz frequency of your garage door opener will determine what remote controls will work with your system. See below to find out which remote to order.

GENERAL SPECIFICATIONS:

Order the 373LM if:

Your garage door opener has a purple learn button, or
Your garage door opener motor head has a purple antenna, or
Your original remote has silver buttons with glowing blue lights, or
Your original remote has black buttons

LiftMaster 373P Premium 315 MHz ERT Garage Door Opener Remote

Electronic Features:

Never fumble in the dark for your garage door remote control again. The new LiftMaster® Premium Remote Control 373P is the only remote control that automatically lights up as you bring your hand nearby, so you'll always know exactly which button to press, even in the dark. Plus, it can control up to three garage door openers or gate operators from greater distances with narrowband radio technology and the reassurance of Security+® anti-theft technology.

GENERAL SPECIFICATIONS:

Features:

Programming Instructions
Sleek and stylish, leather-like grip
Motion-detecting feature streams brilliant blue light from the push-button windows
Can control up to three garage doors or gates
Directional visor clip included
Batteries included; when it is not in use, the remote reverts to "sleep" mode to conserve battery power
Equipped with Security+® anti-theft technology
Compatible with LiftMaster® 3000 series garage door openers and all 315MHz LiftMaster® and ELITE™ gate operators

LiftMaster 374LM 4-Button Remote Control

Electronic Features:

Our basic 4-button remote control isn't so basic. It can operate up to 4 garage doors or gates, and/or turn your garage door opener lights on/off. You can also use it as an extra remote control to turn on lights or small appliances inside your home – all from the comfort of your car. It features Security+® rolling code technology that sends a brand new code every time it is used. One 5-year 3-volt battery is included.

The MHz frequency of your garage door opener will determine what remote controls will work with your system. See below to find out which remote to order.

GENERAL SPECIFICATIONS:

Order the 373LM if:

Your garage door opener has a purple learn button, or
Your garage door opener motor head has a purple antenna, or
Your original remote has silver buttons with glowing blue lights, or
Your original remote has black buttons

LiftMaster 377LM Wireless Keypad

Access your garage and home without the use of a key or a remote control. The LiftMaster® Wireless Keyless Entry can open your garage door using a code that you program directly into the unit. There is also a temporary password option that enables family, friends, or service people to enter the garage/your home without giving them your personal code.

Linear Delta 3 Longrange Receiver

The GRD is a 1-Channel Gate Receiver designed for use with automatic gate operators or systems where a remote antenna is needed. The receiver uses the Delta-3 radio format, with 256 possible codes set by dipswitch.

Linear Delta 3 Mini Transmitter

Model Number: Mini - T

Linear Delta 3 Radio Receiver

1-channel
Model Number: DR

Linear Delta 3 Transmitter 1 button

Linear Delta 3 Transmitter One-button, one-channel, 9-Volt battery powered visor transmitter with removable visor clip, 256 selectable codes.

Linear Delta 3 Transmitter 2 button

Linear Delta 3 Transmitter Two-button, one-channel, 9-Volt battery powered visor transmitter with removable visor clip, 256 selectable codes.

Model Number: DT-2A

Linear DT Wireless KeyPad

The Linear Delta-3 DTKP Keypad Transmitter is one of Linear's series of wireless radio controls designed for use with automatic garage door and gate operators. The Delta-3 radio format provides 256 different codes.

Linear Gate Opener Wireless MegaCode Keyless Entry System MDKP

Electronic Features:

Linear MDKP Exterior Wireless Keypad
Product Number: ACP00878

The MDKP wireless keypad can transmit a unique signal for each 1-6 digit PIN code entered. It has a built-in radio transmitter with a 250-foot range in line-of-sight conditions. It generates a separate transmission code for each user selectable 1-6 digit PIN. Codes are learned by the access controller or receiver, either the maximum number dependent upon the model used. For instance, if the controller is the AP-3, the MDKP can generate 338 unique codes.

To operate the MDKP, a user simply enters a PIN followed by the # key, and the code is transmitted to the receiver for validation. Downlighting can be turned on by pressing the # key twice; it remains on for 30 seconds or until a code is sent. Installation and set-up are simple. The MDKP can be mounted on either a wall or a gooseneck. It is ready to use upon plugging in its 9V lithium battery and programming of user codes.

GENERAL SPECIFICATIONS:

Features:

Factory programmed MegaCode format; internal antenna
1-6 digit PIN for each user
Long life lithium battery
Rugged cast aluminum housing
Built-in downlight

Linear Safety Edge Transmitter Model DTG

Electronic Features:

The DTG Safety Edge Transmitter is compatible with all of Delta-3 products. In a typical installation, the DTG is mounted on a motorized gate, door or barrier arm and wired to a standard exterior safety edge sensor which presents a closed circuit across the connecting wires when an object is hit during the closing of a gate.

GENERAL SPECIFICATIONS:

Safety edge transmitter
Activates one Delta-3 receiver for remote stop or reverse safety edge
No cables or coiled wires
Mounting screws (4) supplied
Power: 9 V battery
Frequency: 310 MHz
Codes: 256 (set by dip switches)
Dimensions: 4 x 4.28 x 2.22 inches

Linear Single Door Gate Controller with a Built-in Receiver AP-5

Linear AP-4 Single Door Gate Controller with a Built-in Receiver
Product Number: ACP00894

The Model AP-4 Single-portal Access Controller is designed for a broad range of access control applications. Its wireless design and small size make it easily adaptable for a variety of access control requirements. Typically, the AP-4 is used to control a door strike, barrier gate, automatic gate or automatic door operator.

The AP-4 contains a high-gain UHF receiver which uses an external antenna to pick up signals from up to 250 feet away. Up to 480 Linear MegaCode® transmitters and one Model MGT safety edge transmitter can be programmed into the AP-4’s memory. The AP-4 will retain its memory, even without power.

Two dry contact relay outputs are provided. One relay is the ACCESS RELAY (K1), which triggers for two seconds each time a programmed transmitter is activated. This relay output connects to the pushbutton or radio input of the access device. The second relay is the OBSTACLE RELAY (K2), which triggers for two seconds when an obstacle signal is sent from a Model MGT safety edge transmitter. This relay output connects to the obstacle input of the access device. An OPEN REQUEST input terminal is supplied for hardwired activation of the access device with an external pushbutton or keyswitch.

The AP-4 can be powered from 12-24 Volts AC or DC. The Form C relay outputs can switch up to 1 Amp each. An EARTH GROUND terminal is provided as an optional connection for maximum lightning and static protection.

Three utility functions can be displayed by pressing the pound (#) key then the digits 1-3. The utility functions display the status of the obstacle transmitter (#1), the total number of transmitters programmed (#2), and the total number of transmitter ID blocks programmed (#3).

The AP-4 has a built-in radio receiver. It has a 250 foot range that can be extended even farther with an optional EXA-2000 antenna.

The AP-4 can fully supervise a Model MGT safety edge transmitter. The system monitors the MGT transmitter for hourly status reports, tamper signals, and low battery signals. A beep will sound every 5 seconds if a fault occurs and the trouble source can be displayed by pressing poundone (#1). A transmitter must be activated twice to trigger the ACCESS RELAY if a supervisory trouble condition exists on the MGT transmitter (unless the MGT has been suspended). To clear the supervisory trouble after servicing, press the CANCEL button.

MultiCode 1-channel Long Range 12-24V Gate Receiver

Features:

Dual frequency - Multi-Code or Stanley compatible; jumper selectable
12-24 Volts AC or DC
Auto voltage sensing - no jumpers to set
Single relay
Supplied with whip antenna, three feet of coaxial cable and bulkhead connector
Power: 12-30 VAC or 10.5 - 30 VDC; 16 mA nominal, 50 mA maximum while relay is triggered
Frequency: 300 MHz and 310 MHz
Dimensions: 3.625 x 5.25 x 1.5 inches

GENERAL SPECIFICATIONS:

Single-channel, dual-frequency (300 MHz Multi-Code & 310 MHz Stanley), 12-24 volt DC or AC powered gate operator receiver. Replaces 109930, 109931, 109940.

MultiCode 1-channel Receiver MC109020

Features:

Exclusive two-way lugs fit under terminal screws or accept push-on terminals in remote sites
11-inch wire antenna supplied
Three tabs for universal operator mounting
Power: for connection to any three-terminal 24 V operator (for higher voltages, consult factory); no need for separate transformer or adapter
Frequency: 300 MHz (310 MHz also available)
Codes: 1,024 (set by dip switches)
Dimensions: 3 x 5.5 x 1.5 inches

GENERAL SPECIFICATIONS:

Single-channel 24 VAC powered receiver with connection lugs for direct attachment to three-terminal garage door operators.

MultiCode 1-channel Visor Transmitter MC3089

Features:

Test/operate LED
Neutral case color
Molded design to comfortably fit the hand
Easy access to battery and dip switch
Operates with all Multi-Code receivers and transmitters
Power: long-life 9 V battery
Frequency: 300 MHz (310 MHz also available)
Codes: 1,024 (set by dip switches)
Dimensions: 3.75 x 2.5 x .875 inches

MultiCode 2-channel Key Ring Transmitter MC3083

Features:

Test/operate LED
Neutral case with fine grain finish
Molded-in hole to accept keychain or keyring
Supplied velcro strip for visor or dashboard mounting
Operates two independent garage doors or an automatic gate and a garage door
Operates with all Multi-Code receivers and transmitters
Power: long-life 12 V battery
Frequency: 300 MHz (310 MHz also available)
Codes: 1,024 (set by sip switches)
Dimensions: 2.5 x 1.5 x .625 inches

MultiCode 2-channel Visor Transmitter MC4120

Features:

MultiCode 2-channel Visor Transmitter
Model Number: 4120
Test/operate LED
Neutral case color
Molded design to comfortably fit the hand
Easy access to battery and dip switch
Operates two independent garage doors or an automatic gate and a garage door
Operates with all Multi-Code receivers and transmitters
Power: long-life 9 V battery
Frequency: 300 MHz (310 MHz also available)
Codes: 1,024 (set by dip switches)
Dimensions: 3.75 x 2.5 x .875 inches

GENERAL SPECIFICATIONS:

MultiCode MC 4120 Two-button, two-channel, 9-Volt battery powered transmitter with removable visor clip, each button can send any of the 1024 selectable codes.

MultiCode 4-channel Visor Transmitter MC4140

Features:

Test/operate LED
Neutral case color
Molded design to comfortably fit the hand
Easy access to battery and dip switch
Operates two independent garage doors or an automatic gate and a garage door
Operates with all Multi-Code receivers and transmitters
Power: long-life 9 V battery
Frequency: 300 MHz (310 MHz also available)
Codes: 1,024 (set by dip switches)
Dimensions: 3.75 x 2.5 x .875 inches

GENERAL SPECIFICATIONS:

Four-button, four-channel, 9-Volt battery powered transmitter with removable visor clip, each button can send any of 256 selectable codes.

MultiCode Safety Edge Transmitter MC105104

Features:

For use with safety edges on gates and large commercial doors
Can be used where hard wires are impractical
Easy to install and mount
More economical than coil/cord sets
Power: 9 V battery
Frequency: 310 MHz
Codes: 1,024 (set by dip switches)
Dimensions: 4 x 4.28 x 2.2 inches

GENERAL SPECIFICATIONS:

Single-channel transmitter that connects to a safety edge sensor for obstacle detection, 9-volt battery powered, 1024 selectable codes.

MultiCode Single Button Key Ring Transmitter MC3060

Features:

Test/operate LED
Neutral case with fine grain finish
Molded-in hole to accept keychain or keyring
Supplied velcro strip for visor or dashboard mounting
Operates with all Multi-Code receivers and transmitters
Power: long-life 12 V battery
Frequency: 300 MHz
Codes: 1,024 (set by sip switches)
Dimensions: 2.5 x 1.5 x .625 inches

MultiCode Wireless Keypad MC4200

Features:

Tamper-resistant and weatherproof
Easy mounting with two screws
12-button, alphanumeric keypad
LED mode indicator
Operates with all Multi-Code receivers
Power: 9 V battery
Codes: 4-digit PIN code access
Frequency: 300 MHz (310 MHz also available)
Dimensions: 2.75 x 6.25 x 1 inches

GENERAL SPECIFICATIONS:

Wireless keypad transmitter, 12-button alphanumeric keypad, 4-digit PIN code access, tamper-resistant, weatherproof, 9-volt battery powered, 1024 selectable transmitter codes.